...
...

MS Channels                                                                            MS Angles

M S Flat                                                                                    MS Round

Our range of structural steel meets the stringent demand of the engineering sector and has wide acceptance in power, telecom, allied industries, precision engineering. The rolled section are highly bendable, ductile, and easily weldable. The products that are manufactured strictly conform to IS standards.

GIPL STRUCTURALS

We manufacture Beams (H Beams and I Beams), Channels, Equal Angles, Round Bars of various sizes and diameters as per IS specifications and customer choice

PRODUCT SPECIFICATION
ProductSTEEL STRUCTURAL SECTIONS
Chemical Composition
ChemicalSymbol% Limit% Variation
CarbonC0.10 – 0.23%0.02
ManganeseMn0.40 – 1.5%0.05
SiliconSi0.40 – Max0.03
SulphurS0.05% – Max0.005
PhosphorusP0.055% – Max0.005
Physical Properties
Material will be supplied in killed

(Al ) condition with limiting carbon equivalent

0.42% Max
Minimum Yield Strength250 MPa
Minimum Tensile Strength410 MPa
Minimum % Elongation23
Range
10 M to 13m Customised length could be supplied based on supply terms and
conditionsLength Tolerance ± 250mm
Size Tolerance/
Weight Tolerance
As per BIS Standard IS 1852
Grade of MaterialAs per IS 2062, E 250 A

Sections in Cu – bearing steel and higher grade material could be
supplied based on supply terms and conditions

Weld abilityWeld able with common M.S. electrodes without pre-heating
Marking/Identification of
Product
Every Structural Section is embossed (hot rolling) with size detail, ISI
mark and Go’s logo/Mark along the length at regular intervals.
Ordering InformationWhile placing an order, the following technical information would be
needed :

  • Size & length of each piece and quantity
  • Steel specification with grade/chemical composition/physical properties
  • Test certificates requirement
  • Special Requirements if any
1Design Standard: IS: 800 or any other equivalent international standard for structural design.
2Dead Load, Imposed loads and Wind loads to be assumed in design as per specified in IS: 875.
3Imposed Loads arising from equipment to be assumed in design as per manufacturer’s data.
4Earthquake Loads shall be assumed in design as per IS: 1893
5Handlings Loads, Erection Loads, effect of temperature change and load due to settlement of foundation shall be considered as per IS: 800 stipulations.

Technical Specifications

SectionDimensions(mm)Sectional Weight(Kg/m)Lower Limit(Kg/m)
Angels20 x 20 x 3/40.9/1.16 to 12 mt
25 x 25 x 3/4/51.1/1.4/1.8
30 x 30 x 3/4/51.4/1.8/2.2
35 x 35 x 3/4/5/61.6/2.1/2.6/3.0
40 x 40 x 3/4/5/61.8/2.4/3.0/3.5
45 x 45 x 3/4/5/62.1/2.7/3.4/4.0
50 x 50 x 3/4/5/62.3/3.0/3.8/4.5
55 x 55 x 4/5/6/83.3/4.1/4.9/6.4
60 x 60 x 4/5/6/83.7/4.5/5.4/7.0
65 x 65 x 4/5/6/84.0/4.9/5.8/7.7
70 x 70 x 5/6/8/105.3/6.3/8.3/10.2
75 x 75 x 5/6/8/105.7/6.8/8.9/11.0
80 x 80 x 6/8/10/127.3/9.6/11.8/14.0
90 x 90 x 6/8/10/128.2/10.8/13.4/15.8
100 x 100 x 6/8/10/129.2/12.1/14.9/17.7
110 x 110 x 8/10/12/1613.4/16.6/19.7/25.7
130 x 130 x 8/10/12/1615.9/19.7/23.5/30.7
SectionDimensions(mm)Sectional Weight(Kg/m)Upper Limit(Kg/m)Lower Limit(Kg/m)
M.S. FLAT20 x 50.790.82950.7663
20 x 60.940.9870.9118
25 x 511.050.97
25 x 61.21.261.64
30 x 51.21.261.64
30 x 61.41.471.358
35 x 51.41.471.358
35 x 61.61.681.552
40 x 51.61.681.552
40 x 61.881.9741.8236
45 x 51.81.891.746
45 x 62.12.2052.037
50 x 522.11.94
50 x 62.42.522.328
55 x 52.22.312.134
55 x 62.62.732.522
60 x 52.42.522.328
60 x 62.82.942.716
65 x 84.14.3053.977
65 x 105.15.3554.947
70 x 84.44.624.268
70 x 105.55.7755.335
75 x 1810.611.1310.282
75 x 2011.812.3911.446
80 x 855.254.85
80 x 106.36.6156.111
80 x 127.57.8757.275
90 x 85.75.9855.529
90 x 107.17.4556.887
90 x 128.58.9258.245
100 x 86.36.6156.111
100 x 107.88.197.566
100 x 129.49.879.118
SectionDimensions(mm)Sectional Weight(Kg/m)Upper Limit(Kg/m)Lower Limit(Kg/m)
M.S. ROUND60.2220.2370.206
80.3950.4230.367
100.6170.660.574
120.8880.9320.844
161.581.6591.501
202.472.5442.396
253.853.9653.734
284.834.9744.685
326.316.4996.121
409.8610.4569.564
SectionDimensions(mm)Sectional Weight(Kg/m)Lower Limit(Kg/m)
Channels75 x 40 x 4.87.146 to 12 mt
100 x 50 x 5.09.56
125 x 65 x 5.313.1
150 x 75 x 5.716.8

About us

  • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard

CSR Activity

  • Lorem Ipsum is simply dummy text of the printing and typesetting industry. Lorem Ipsum has been the industry's standard dummy text ever since the 1500s, when

Registered Office

Working hours

  • Weekdays 8:00 - 20:00
  • Saturday 9:00 - 16:00
  • Sunday Closed
  • Holidays 10:00 - 14:00